How to Remove and also Replace a Bathtub.
How to Remove and also Replace a Bathtub.
Blog Article
The article which follows pertaining to A Step-by-Step Guide to Installing a Bathtub is seriously fascinating. Try it and make your own assumptions.
Mounting a bathtub isn't precisely brain surgery, yet it does require solid plumbing, carpentry, and also sometimes, tiling skills. Changing an old bath tub with a new one is likewise a reasonably hard project. If the old tub is conveniently easily accessible, the task can relocate speedily; if you have to open up a wall surface to remove the old tub as well as place the new bath tub, the job is much harder. In either case, the job is within a house handyman's abilities, although you will certainly need a helper to move out the old tub as well as embeded in the brand-new one. See to it you have actually certified on your own for the task and also fit attempting it. Rather than working with a contractor to take over a halfway-completed project, it is much better to think about using one prior to you start. Opportunities are you may require a specialist plumber to make tube links.
This write-up will certainly help you install a new bath tub in your restroom if you have currently acquired a new tub as well as don't require to transform the setup of your previous water supply pipes.
Your tools as well as product list must make up the following:
Planning for the Installment
To start with, the supporting frame supplied with the bath should be fitted (if required) according to the producer's directions. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is very important to ensure that if the tap comes with a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the taps unit to stop pressure on the tub.
Fit the versatile tap adapters to the bottom of both taps using 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you make use of every one of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath must now prepare to be fitted in its final placement.
Removing Old Touches
If you need to change old faucets with new ones as a part of your installation, after that the first thing you ought to do is disconnect the water. After doing so, switch on the faucets to drain pipes any kind of water staying in the system. The procedure of eliminating the existing taps can be rather problematic because of the restricted gain access to that is often the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the faucets. Have a cloth all set for the staying water that will certainly come from the pipelines. When the supply pipes have actually been removed, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary faucets from turning throughout this process. When the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any old sealing substance.
Before proceeding to fit the brand-new faucets, compare the pipe links on the old taps to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new faucets to fit.
Mounting the Tub
Utilizing both wooden boards under its feet, place the tub in the called for position. The wooden boards are practical in evenly spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto four little factors.
The next goal is to make certain that the bath tub is leveled all round. This can be achieved by checking the spirit level and also readjusting the feet on the bathtub up until the level reads level.
To mount taps, fit the bottom of the outermost adaptable tap port to the ideal supply pipeline by making a compression join; then do the very same for the various other faucet.
Switch on the water supply as well as inspect all joints as well as brand-new pipework for leakages as well as tighten them if required. Fill the tub and likewise examine the overflow electrical outlet and also the regular electrical outlet for leaks.
Finally, fix the bath paneling as described in the manufacturer's instruction manual. Tiling and sealing around the bathtub ought to wait up until the bath tub has actually been utilized at the very least when as this will certainly settle it into its final position.
Fitting New Taps
If the tails of the new taps are plastic, then you will certainly require a plastic adapter to stop damages to the string. One end of the port fits on the plastic tail of the tap as well as the other end offers a connection to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin ensuring that the washers are in place between the faucet and also the sink. Safeguard the faucet in position with the maker supplied backnut. As soon as the faucet is safely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with regular tap connectors. The former kind ought to be attached to the tap ends first, tightening just by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the location where the bathroom meets the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is essential as the fitting can move sufficient to split a stiff seal, causing the water to pass through the wall between the bathroom and the tiling, leading to issues with moisture and also feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealants to assimilate your fixtures and also installations. They are offered in tubes and cartridges, and can securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of soaked paper or soft rope. Keep in mind to always load the tub with water before securing, to enable the activity experienced when the bathtub is in usage. The sealant can fracture relatively early if you do not take into account this activity prior to securing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally quickly readily available on the marketplace. It is advisable to fit the floor tiles using waterproof or waterproof glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you like more info about How to Install a Bathtub Yourself? Place feedback further down. We will be pleased to listen to your suggestions about this blog entry. In hopes that you come back again later on. Appreciated our entry? Please share it. Let another person locate it. Thanks a lot for your time. Please check up our blog back soon.
Need Help? Hire Us Now! Report this page